board_configuration.cpp

Go to the documentation of this file.

/**
 * See https://rusefi.com/s/super-uaefi
 *
 * @author Andrey Belomutskiy, (c) 2012-2023
 */
 
#include "pch.h"
#include "defaults.h"
#include "hellen_meta.h"
#include "hellen_leds_100.cpp"
#include "board_overrides.h"
//#include "connectors/generated_board_pin_names.h"
 
static void setInjectorPins() {
    engineConfiguration->injectionPins[0] = Gpio::MM100_INJ1;
    engineConfiguration->injectionPins[1] = Gpio::MM100_INJ2;
    engineConfiguration->injectionPins[2] = Gpio::MM100_INJ3;
    engineConfiguration->injectionPins[3] = Gpio::MM100_INJ4;
    engineConfiguration->injectionPins[4] = Gpio::MM100_INJ5;
    engineConfiguration->injectionPins[5] = Gpio::MM100_INJ6;
}
 
static void setIgnitionPins() {
    engineConfiguration->ignitionPins[0] = Gpio::MM100_IGN1;
    engineConfiguration->ignitionPins[1] = Gpio::MM100_IGN2;
    engineConfiguration->ignitionPins[2] = Gpio::MM100_IGN3;
    engineConfiguration->ignitionPins[3] = Gpio::MM100_IGN4;
    engineConfiguration->ignitionPins[4] = Gpio::MM100_IGN5;
    engineConfiguration->ignitionPins[5] = Gpio::MM100_IGN6;
}
 
static void setupDefaultSensorInputs() {
    engineConfiguration->tps1_1AdcChannel = MM100_IN_TPS_ANALOG;
    engineConfiguration->tps1_2AdcChannel = MM100_IN_AUX1_ANALOG;
//  engineConfiguration->map.sensor.hwChannel = PIN_D9;
 
    setPPSInputs(MM100_IN_PPS_ANALOG, MM100_IN_AUX2_ANALOG);
 
    engineConfiguration->clt.adcChannel = MM100_IN_CLT_ANALOG;
    engineConfiguration->iat.adcChannel = MM100_IN_IAT_ANALOG;
 
    engineConfiguration->triggerInputPins[0] = Gpio::MM100_UART8_TX; // VR2 max9924 is the safer default
    engineConfiguration->camInputs[0] = Gpio::MM100_IN_D1; // HALL1
    engineConfiguration->camInputs[1] = Gpio::MM100_IN_D2; // HALL2
 
  engineConfiguration->vehicleSpeedSensorInputPin = Gpio::MM100_IN_D3;
}
 
static void super_uaefi_boardConfigOverrides() {
    setHellenMegaEnPin();
    setHellenVbatt();
 
    hellenMegaSdWithAccelerometer();
 
  engineConfiguration->vrThreshold[0].pin = Gpio::MM100_OUT_PWM6;
 
    setHellenCan();
 
    setDefaultHellenAtPullUps();
 
}
 
bool validateBoardConfig() {
  return true;
}
 
void setUaefiDefaultETBPins() {
  // users would want to override those if using H-bridges for stepper idle control
  setupTLE9201IncludingStepper(/*PWM controlPin*/Gpio::MM100_OUT_PWM3, Gpio::MM100_OUT_PWM4, Gpio::MM100_SPI2_MISO);
  setupTLE9201IncludingStepper(/*PWM controlPin*/Gpio::MM100_OUT_PWM5, Gpio::MM100_SPI2_MOSI, Gpio::MM100_USB1ID, 1);
}
 
/**
 * @brief   Board-specific configuration defaults.
 *
 
 *
 */
static void super_uaefi_boardDefaultConfiguration() {
    setInjectorPins();
    setIgnitionPins();
    setUaefiDefaultETBPins();
 
  setHellenMMbaro();
 
    engineConfiguration->displayLogicLevelsInEngineSniffer = true;
    engineConfiguration->isSdCardEnabled = true;
 
    engineConfiguration->enableSoftwareKnock = true;
 
    engineConfiguration->canTxPin = Gpio::MM100_CAN_TX;
    engineConfiguration->canRxPin = Gpio::MM100_CAN_RX;
 
  engineConfiguration->mainRelayPin = Gpio::MM100_IGN7;
    engineConfiguration->fanPin = Gpio::MM100_IGN8;
    engineConfiguration->fuelPumpPin = Gpio::MM100_OUT_PWM2;
 
    // SPI3 for on-board EGT
    engineConfiguration->is_enabled_spi_3 = true;
    // MOSI not needed, we have one-way communication here
    engineConfiguration->spi3misoPin = Gpio::C11;
    engineConfiguration->spi3sckPin = Gpio::C10;
    engineConfiguration->max31855_cs[0] = Gpio::A15;
    engineConfiguration->max31855spiDevice = SPI_DEVICE_3;
 
    // "required" hardware is done - set some reasonable defaults
    setupDefaultSensorInputs();
    engineConfiguration->enableVerboseCanTx = true;
 
    engineConfiguration->etbFunctions[0] = DC_Throttle1;
 
    // Some sensible defaults for other options
    setCrankOperationMode();
 
    setAlgorithm(engine_load_mode_e::LM_SPEED_DENSITY);
 
    engineConfiguration->injectorCompensationMode = ICM_FixedRailPressure;
 
#ifndef EFI_BOOTLOADER
    setCommonNTCSensor(&engineConfiguration->clt, HELLEN_DEFAULT_AT_PULLUP);
    setCommonNTCSensor(&engineConfiguration->iat, HELLEN_DEFAULT_AT_PULLUP);
#endif // EFI_BOOTLOADER
 
    setTPS1Calibration(100, 650);
    hellenWbo();
}
 
static Gpio OUTPUTS[] = {
    Gpio::MM100_INJ1, // 13B INJ_1
    Gpio::MM100_INJ2, // 12B INJ_2
    Gpio::MM100_INJ3, // 11B INJ_3
    Gpio::MM100_INJ4, // 10B INJ_4
    Gpio::MM100_INJ5, // 9B INJ_5
    Gpio::MM100_INJ6, // 8B INJ_6
    Gpio::MM100_SPI2_CS, // 19B INJ_7
    Gpio::MM100_SPI2_SCK, // 18B INJ_8
    Gpio::MM100_INJ7, // 20B LS1
    Gpio::MM100_INJ8, // 21B LS2
    Gpio::MM100_OUT_PWM1, // 22B LS3
    Gpio::MM100_OUT_PWM2, // 31C LS4
    Gpio::MM100_IGN7, // 30C LS5_HOT
    Gpio::MM100_IGN8, // 29C LS6_HOT
    Gpio::MM100_IGN1, // Coil 1
    Gpio::MM100_IGN2, // Coil 2
    Gpio::MM100_IGN3, // Coil 3
    Gpio::MM100_IGN4, // Coil 4
    Gpio::MM100_IGN5, // Coil 5
    Gpio::MM100_IGN6, // Coil 6
    Gpio::MM100_LED2_GREEN, // 20D High Side Output
};
 
int getBoardMetaOutputsCount() {
    return efi::size(OUTPUTS);
}
 
int getBoardMetaLowSideOutputsCount() {
  return getBoardMetaOutputsCount() - 7;
}
 
Gpio* getBoardMetaOutputs() {
    return OUTPUTS;
}
 
int getBoardMetaDcOutputsCount() {
    return 2;
}
 
void setup_custom_board_overrides() {
    custom_board_DefaultConfiguration = super_uaefi_boardDefaultConfiguration;
    custom_board_ConfigOverrides = super_uaefi_boardConfigOverrides;
}