board_configuration.cpp

Go to the documentation of this file.

/**
 * @file boards/hellen/hellen72/board_configuration.cpp
 *
 *
 * @brief Configuration defaults for the Hellen72 board
 *
 * See https://rusefi.com/s/hellen72
 *
 * @author andreika <prometheus.pcb@gmail.com>
 * @author Andrey Belomutskiy, (c) 2012-2020
 */
 
#include "pch.h"
#include "hellen_meta.h"
#include "board_overrides.h"
 
static void setInjectorPins() {
    engineConfiguration->injectionPins[0] = Gpio::G7;
    engineConfiguration->injectionPins[1] = Gpio::G8;
    engineConfiguration->injectionPins[2] = Gpio::D11;
    engineConfiguration->injectionPins[3] = Gpio::D10;
}
 
static void setIgnitionPins() {
    engineConfiguration->ignitionPins[0] = H176_IGN_1; // 3F - IGN_1 (1&4)
    engineConfiguration->ignitionPins[1] = Gpio::Unassigned ; // Gpio::E4
    engineConfiguration->ignitionPins[2] = Gpio::E5; // 3I - IGN_2 (2&3)
    engineConfiguration->ignitionPins[3] = Gpio::Unassigned; // Gpio::E3
}
 
static void setupDefaultSensorInputs() {
    // trigger inputs
    engineConfiguration->triggerInputPins[0] = Gpio::B1;
    engineConfiguration->triggerInputPins[1] = Gpio::Unassigned;
    // Direct hall-only cam input
    engineConfiguration->camInputs[0] = Gpio::A6;
 
    engineConfiguration->tps1_1AdcChannel = EFI_ADC_4;
 
    engineConfiguration->mafAdcChannel = EFI_ADC_10;
    engineConfiguration->map.sensor.hwChannel = EFI_ADC_11;
 
    engineConfiguration->afr.hwChannel = EFI_ADC_1;
 
    engineConfiguration->clt.adcChannel = H144_IN_CLT;
 
    engineConfiguration->iat.adcChannel = H144_IN_IAT;
}
 
#include "hellen_leds_176.cpp"
 
static void hellen_MiataNB2_boardConfigOverrides() {
    setHellenVbatt();
 
    if (engine->engineState.hellenBoardId == -1) {
        // Rev a-d use SPI3 for SD card
        setHellenSdCardSpi3();
    } else {
        // Revs E and later use SPI2 for SD card
        setHellenSdCardSpi2();
    }
 
    // NB2 still uses L6205PD
    engineConfiguration->etbIo[0].directionPin1 = Gpio::H144_OUT_PWM3; // ETB+
    engineConfiguration->etbIo[0].directionPin2 = Gpio::H144_OUT_PWM4; // ETB-
    engineConfiguration->etbIo[0].controlPin = Gpio::H144_OUT_PWM2; // ETB_EN
    engineConfiguration->etb_use_two_wires = true;
 
    setDefaultHellenAtPullUps();
 
    setHellenCan();
}
 
/**
 * @brief   Board-specific configuration defaults.
 *
 
 *
 
 */
static void hellen_MiataNB2_boardDefaultConfiguration() {
    setInjectorPins();
    setIgnitionPins();
 
    engineConfiguration->enableSoftwareKnock = true;
 
    engineConfiguration->acRelayPin = Gpio::H15;
    engineConfiguration->acSwitch = Gpio::B0;
    engineConfiguration->acSwitchMode = PI_PULLUP;
 
    engineConfiguration->vehicleSpeedSensorInputPin = Gpio::H144_IN_VSS;
    engineConfiguration->clutchDownPin = Gpio::H144_IN_RES3;
    engineConfiguration->clutchDownPinMode = PI_INVERTED_DEFAULT;
 
    engineConfiguration->fuelPumpPin = Gpio::G2;    // OUT_IO9
    engineConfiguration->idle.solenoidPin = Gpio::D14;  // OUT_PWM5
    engineConfiguration->fanPin = Gpio::D12;    // OUT_PWM8
    engineConfiguration->fan2Pin = Gpio::D9;
    engineConfiguration->enableFan2WithAc = true;
    engineConfiguration->mainRelayPin = Gpio::I2;   // OUT_LOW3
    engineConfiguration->vvtPins[0] = Gpio::I0;    // 4R - VVT (O5)
 
    engineConfiguration->tachOutputPin = Gpio::D13; // 3O - TACH (PWM7)
    engineConfiguration->alternatorControlPin = Gpio::D15; // 3M - ALTERN (PWM6)
 
 
    // "required" hardware is done - set some reasonable defaults
    setupDefaultSensorInputs();
 
    engineConfiguration->cylindersCount = 4;
    engineConfiguration->firingOrder = FO_1_3_4_2;
 
    engineConfiguration->ignitionMode = IM_INDIVIDUAL_COILS; // IM_WASTED_SPARK
 
 
 
    hellenWbo();
}
 
void setup_custom_board_overrides() {
    custom_board_DefaultConfiguration = hellen_MiataNB2_boardDefaultConfiguration;
    custom_board_ConfigOverrides = hellen_MiataNB2_boardConfigOverrides;
}